Page Comparison

#-------------------------------------------------------------------------------
# 1.4] EMail Server Settings
#-------------------------------------------------------------------------------
# The server to be used for mail transactions (eg smtp.google.com if Internet-enabled, contact your sysadmin if not):
mail.server=
# Base-64 encoded SHA-256Jasypt hashencrpyion of username (using salt/"password" "infinit.e"):
mail.username=
# Base-64 encoded SHA-256Jasypt hashencrpyion of password (using salt/"password" "infinit.e"):
mail.password=
# This URL is used as the base for links included in the 
# So should point to an accessible REST endpoint (eg the same as ui.end.point.url below)
# If this is left commented out, it defaults to the browser domain (ie location of GUI)
#url.root=http://MY_REST_ENDPOINT/api/

#-------------------------------------------------------------------------------
# 1.8] MongoDB Properties
#-------------------------------------------------------------------------------
# MongoDB config server or servers (must be 1 or 3 comma separated IPs/hosts), non-EC2/AWS installations only
# (Can be used in AWS mode for legacy clusters only, to hardwire server order)
db.config.servers=
db.replica.sets=
#---------
# Replica set configuration (non-EC2/AWS installations only): comma-separated list of either all IPs or all hostnames within a replica set, semi-colon-separated for multiple replica sets
# (eg "A,B;C,D" where A-D are IP addresses or hostnames would create 2 shards with 2 hosts each "A,B;A,B" would create 2 shards both on the same replica set, etc)
db.replica.sets=
#-------------------------------------
# db.cluster.subnet - used for non-EC2/AWS only installations to help mongodb configurations
# identify proper host ip addresses, e.g. 127.0.0.------------------------
# db.cluster.subnet - used for non-EC2/AWS only installations to help mongodb configurations
# identify proper host ip addresses, e.g. 127.0.0. - these are compared against the IPs in db.replica.sets
# Can also be one of the following: if blank then assumes that the db.replica.sets will be a list of short hostnames - if "FQDN" then assumes that the db.replica.sets will be a list of fully qualified hostnames
db.cluster.subnet=

#-------------------------------------------------------------------------------
# 1.10] Elasticsearch Properties
#-------------------------------------------------------------------------------
# Cluster name 
# Any unique name within the EC2 cluster/subnet: 
elastic.cluster=
#----------------------------------------------
# ES nodes, e.g.: elastic.search.nodes=['NODE1:9300','NODE2:9300','NODE3:9300':]
# Needed if discovery.mode=zen (not EC2/AWS), a set of IPs to try (>= 1 must be running elasticsearch)
elastic.search.nodes=
# If any node sees less than this number of connections it will take itself down
# For a single node, should be 0 (default), for a 2-node system, should be 1, for large clusters
# ideally would be CLUSTER_SIZE - #REPLICAS (and >=2), but 2 is workable if the size is not fixed
# (if this is set too low then split brain situations may not be detected)
elastic.search.min_peers=0

#-------------------------------------------------------------------------------
# 2.8] MongoDB Properties
#-------------------------------------------------------------------------------
# (server/port should normally point to localhost:27017), where API nodes have a mongos
db.server=localhost
db.port= 27017
# db.sharded - 0 = false and 1 = true
db.sharded=1
# The max number of documents to store (eg 10M). Docs will be dropped in order of age.
# (Not currently supported):
db.capacity=10000000
# MongoDB config server or servers (must be 1 or 3 comma separated IPs), non-EC2/AWS installations only
db.config.servers=
db.replica.sets=
#----------------------------------------------
# db.cluster.subnet - used for non-EC2/AWS only installations to help mongodb configurations
# identify proper host ip addresses, e.g. 127.0.0.
db.cluster.subnet=
#----------------------------------------------
# The location from which to fetch the geo.bson dump used for feature.geo
# can start s3://, http:// or https://, else is assumed to be a file, eg
#db.geo_archive=s3://config.saas.infinite.ikanow.com/geo.bson.tar.gz
# Can always be retrieved here
db.geo_archive=http://wwwyum.ikanow.com/infinit.e-preinstall/artifacts/geo.bson.tar.gz

#-------------------------------------------------------------------------------
# 2.10] Elasticsearch Properties
#----------------------------------------------
# Discovery mode = ec2 (if running on AWS) or zen (specify a list of IPs below):
elastic.node.discovery=ec2
#----------------------------------------------
# ES nodes, e.g.: elastic.search.nodes='NODE1:9300','NODE2:9300','NODE3:9300':
# Needed if discovery.mode=zen (not EC2/AWS), a set of IPs to try (>= 1 must be running elasticsearch)
elastic.search.nodes=
#-------------------------------------------------------------------------------
# mlockall = should equal true except if running on a machine with < 4GB of RAM
bootstrap.mlockall=true
# (Should normally be localhost:9300, unless an API node is running with no index node) 
elastic.url=localhost:9300
# (Should normally be localhost:9300, unless an API node is running with no index node) 
elastic.url=localhost:9300
# If you know your logstash and elasticsearch versions are matched up, you can improve the output performance by setting this to "binary"
elastic.logstash=http

#-------------------------------------------------------------------------------
# 2.16] Enterprise variables - ignore for non-enterprise installs
#-------------------------------------------------------------------------------
# The location of the case manager app server - set to "local" to point to <domain>/caseserver
# NOTE THAT THE DOMAIN MUST MATCH THE URL OF THE MAIN GUI OR AUTHENTICATION WON'T WORK
#app.case.api.url=local 
#####
# Proxy settings for port 8090
# The location of the case manager GUI - setReverse toProxies "local"requests to point to <domain>:8090/casemanager
# If (redirectsthe to 8090/nuxeo)
# NOTE THAT THE DOMAIN MUST MATCH THE URL OF THE MAIN GUI OR AUTHENTICATION WON'T WORK
#app.case.url=localcase manager server is located on a different domain name, change casemanager.master to be the domain name of that server.
casemanager.master=localhost.localdomain
# The location of the casesplunk managermonitor GUIserver - Reverse Proxies requests to <domain>:8090/casemanagersplunk
# If the casesplunk manager server is located on a different domain name, change casemanagermonitor.master to be the domain name of that server.
casemanagermonitor.master=localhost.localdomain
 
####
# Enterprise settings need by the GUI
# The location of the splunkcase manager monitorapp server - Reverse Proxies requests set to "local" to point to <domain>:8090/splunkcaseserver
# If the splunk server is located on a different domain, change monitor.master to be the domain name of that server.
monitor.master=localhost
#This is the name of the domain which the SSL certificates bound to. If it is not set, clients will get a domain mismatch error when connecting to the enterprise server.
httpd.domainName=notset.mydomainname.comNOTE THAT THE DOMAIN MUST MATCH THE URL OF THE MAIN GUI OR AUTHENTICATION WON'T WORK
#app.case.api.url=local
# The location of the case manager GUI - set to "local" to point to <domain>:8090/casemanager
# (redirects to 8090/casemanage)
# NOTE THAT THE DOMAIN MUST MATCH THE URL OF THE MAIN GUI OR AUTHENTICATION WON'T WORK
#app.case.url=local

#-------------------------------------------------------------------------------